Search found 257 matches
Re: Studiomaster Powerhouse 300
I found a couple of pins on a pcb that were not connected to the rails so I hard wired them and hey presto it all works!
- Forum: DIY Electronics & Studio Design Topic: Studiomaster Powerhouse 300 Replies: 3 Views: 202
Studiomaster Powerhouse 300
I have acquired one of these and everything works ok apart from the reverb and output LEDs.
The reverb shows a constant overload light warning and doesn’t.
All tge output LEDs are on all the time.
Anyone experienced with these?
The reverb shows a constant overload light warning and doesn’t.
All tge output LEDs are on all the time.
Anyone experienced with these?
- Forum: DIY Electronics & Studio Design Topic: Studiomaster Powerhouse 300 Replies: 3 Views: 202
Nectar 4 Voices Module
I have bought Izotope Nectar 4 Standard but the voices module just presents with a white screen.All the other parts work fine.
I have it running under Windows 7 could this be the issue?
I have it running under Windows 7 could this be the issue?
- Forum: Windows Music Topic: Nectar 4 Voices Module Replies: 3 Views: 94
Re: Active Pick Up Pot Size
Update!
It was the bridge pick up and it works!
Thanks for the help.
It was the bridge pick up and it works!
Thanks for the help.
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Re: Active Pick Up Pot Size
I am away just now but will check when I get home.
Thanks again.
Thanks again.
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Re: Active Pick Up Pot Size
Cheers for that.
Don’t know if it is the bridge or neck pick up but I could wire it up to see if it works.
Don’t know if it is the bridge or neck pick up but I could wire it up to see if it works.
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Re: Active Pick Up Pot Size
I should not have been so lazy! I have looked it up and think the pots are 50k!!
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Re: Active Pick Up Pot Size
I don’t have the pick up to hand but think it was an IBZ-LZ which I think is an Ibanez model.I think it needs a 3volt power supply.
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Active Pick Up Pot Size
I have an active pick up to install in a guitar.
Do active pick ups need different resistance values on the control pots than non active ones?
Do active pick ups need different resistance values on the control pots than non active ones?
- Forum: Guitar Technology Topic: Active Pick Up Pot Size Replies: 10 Views: 147
Re: Strymon Iridium
I bought an Iridium and am very happy with it!
It’s nice and simple which suits me.
It’s nice and simple which suits me.
- Forum: Guitar Technology Topic: Strymon Iridium Replies: 11 Views: 640
Strymon Iridium
Thinking of getting Strymon Iridium for my birthday.
I already have an Atomic Amplifire and was wondering if the Strymon would be any better? I would be using it for direct recording.
Maybe just another case of gear lust!
I already have an Atomic Amplifire and was wondering if the Strymon would be any better? I would be using it for direct recording.
Maybe just another case of gear lust!
- Forum: Guitar Technology Topic: Strymon Iridium Replies: 11 Views: 640
Re: Behringer Eurodesk 1604A
Yes it was quite therapeutic doing it!
Bit like a jigsaw puzzle.
Bit like a jigsaw puzzle.
- Forum: DIY Electronics & Studio Design Topic: Behringer Eurodesk 1604A Replies: 6 Views: 287
Re: Behringer Eurodesk 1604A
**update**
I tracked the problem down to a fader which had gone open circuit.
Got one off eBay and it now works ok.
Behringer gear not the best to work on!
I tracked the problem down to a fader which had gone open circuit.
Got one off eBay and it now works ok.
Behringer gear not the best to work on!
- Forum: DIY Electronics & Studio Design Topic: Behringer Eurodesk 1604A Replies: 6 Views: 287
Behringer Eurodesk 1604A
One of the channels on the desk works when you depress the pfl button but when not on pfl it doesn’t pass to the main buss.
The other channels work fine.
Any ideas?
The other channels work fine.
Any ideas?
- Forum: DIY Electronics & Studio Design Topic: Behringer Eurodesk 1604A Replies: 6 Views: 287
Re: MXL R144 Ribbon Mic
I find that I need to use a fair bit of low end roll off with the Mxl but to me it still sounds better than an sm57 which I find a bit “brittle”.
Wise advice I think I have a bit of gear lust!
Wise advice I think I have a bit of gear lust!
- Forum: Recording: Gear & Techniques Topic: MXL R144 Ribbon Mic Replies: 2 Views: 219
MXL R144 Ribbon Mic
I have been using an MXL ribbon mic on my guitar amp for ages.
I like the sound of the ribbon mic on guitar amps.
I am thinking of maybe upgrading the mic to say a Rode NTR.
Just wondering if it would be worth it?
I like the sound of the ribbon mic on guitar amps.
I am thinking of maybe upgrading the mic to say a Rode NTR.
Just wondering if it would be worth it?
- Forum: Recording: Gear & Techniques Topic: MXL R144 Ribbon Mic Replies: 2 Views: 219
VHT Special 6 Ultra
I have been offered a VHT Special 6 Ultra.Anyone used one?
I need an amp that will sound and record well at low volumes!
I need an amp that will sound and record well at low volumes!
- Forum: Guitar Technology Topic: VHT Special 6 Ultra Replies: 0 Views: 200
Re: Weller Soldering Iron
The Weller iron that Dave helped me with is great!
I have improved my soldering skills as well.
I have improved my soldering skills as well.
- Forum: DIY Electronics & Studio Design Topic: Weller Soldering Iron Replies: 96 Views: 3336
Re: Pedal Board Power Supply
I think I ordered the EU power supply in error but the photo was of a UK power supply.
- Forum: Guitar Technology Topic: Pedal Board Power Supply Replies: 11 Views: 728
Re: Pedal Board Power Supply
I bought it from Amazon.They gave me a 10% rebate to buy a UK one.
- Forum: Guitar Technology Topic: Pedal Board Power Supply Replies: 11 Views: 728